How Morse code timing works
Morse code is built from one time unit, the length of a dot. The ITU rules set everything else from it:
gap between letters = 3 dots · gap between words = 7 dots
dot length (seconds) = 1.2 ÷ WPM
Speed in words per minute (WPM) uses the standard word PARIS, which is exactly 50 dot units long including the gap after it. At W words per minute you send 50 × W dots a minute, so one dot lasts 60 ÷ (50 × W) = 1.2 ÷ W seconds.
Worked example
SOS is S (· · ·), O (− − −), S (· · ·). Each S is 3 dots plus 2 one-unit gaps = 5 units. The O is 3 dashes (9 units) plus 2 gaps = 11 units. Add two 3-unit gaps between the letters: 5 + 11 + 5 + 6 = 27 units. At 20 WPM a dot is 1.2 ÷ 20 = 0.06 seconds, so SOS takes 27 × 0.06 = 1.62 seconds.
PARIS on its own is 43 units (the last 7-unit word gap brings it to 50), so at 20 WPM it takes 43 × 0.06 = 2.58 seconds.
Morse code chart: letters
| Letter | Morse | Letter | Morse |
|---|---|---|---|
| A | .- | N | -. |
| B | -... | O | --- |
| C | -.-. | P | .--. |
| D | -.. | Q | --.- |
| E | . | R | .-. |
| É | ..-.. | S | ... |
| F | ..-. | T | - |
| G | --. | U | ..- |
| H | .... | V | ...- |
| I | .. | W | .-- |
| J | .--- | X | -..- |
| K | -.- | Y | -.-- |
| L | .-.. | Z | --.. |
| M | -- |
Numbers
| Figure | Morse | Figure | Morse |
|---|---|---|---|
| 1 | .---- | 6 | -.... |
| 2 | ..--- | 7 | --... |
| 3 | ...-- | 8 | ---.. |
| 4 | ....- | 9 | ----. |
| 5 | ..... | 0 | ----- |
Punctuation and signs
| Sign | Name | Morse |
|---|---|---|
| . | Full stop (period) | .-.-.- |
| , | Comma | --..-- |
| : | Colon or division sign | ---... |
| ? | Question mark | ..--.. |
| ' | Apostrophe | .----. |
| - | Hyphen, dash or minus sign | -....- |
| / | Fraction bar or division sign | -..-. |
| ( | Left bracket | -.--. |
| ) | Right bracket | -.--.- |
| " | Quotation marks | .-..-. |
| = | Double hyphen (also used for =) | -...- |
| + | Cross or plus sign | .-.-. |
| × | Multiplication sign (same as X) | -..- |
| @ | Commercial at | .--.-. |
The ITU table has no signs for !, &, ;, $ or _. Those are left out of the translation and listed under the result, so you can spell them out instead. Accented letters other than É aren't in the table either.
Service signals
These are sent as one run with no letter gaps. The translator shows them in brackets when you decode them.
| Service signal | Morse |
|---|---|
| Understood | ...-. |
| Error (eight dots) | ........ |
| Invitation to transmit (same as K) | -.- |
| Wait | .-... |
| End of work | ...-.- |
| Starting signal | -.-.- |
Limitations
- This uses International (ITU) Morse code. American Morse, the old railroad telegraph code, is different.
- Amateur radio has extra procedure signs and abbreviations that aren't in the ITU table, such as SK and the 73 sign-off. They decode here as their separate letters.
- Sound plays only after you press Play, and only on your device. Some phones stay silent while the ringer switch is off.
Sources
- ITU-R Recommendation M.1677-1 (10/2009): International Morse code the character table and the spacing rules.
- ITU-R M.1677-1 full text (PDF)