Enter the walls, gables, windows and doors to get the area to cover in square feet and siding squares, with extra for waste.
How siding is estimated
Siding is sold and priced by the square: 100 square feet, an area 10 ft by 10 ft.
Walls = Σ (width × height)
Gables = number × ½ × base × height
Net area = walls + gables − windows − doors
Squares = net area × (1 + waste % ÷ 100) ÷ 100
Worked example
A 40 × 30 ft house with 9 ft walls: 2 × 40 × 9 + 2 × 30 × 9 = 1,260 sq ft. Two gable ends 30 ft wide and 8 ft high add 2 × ½ × 30 × 8 = 240 sq ft. Take off 10 windows of 3 × 5 ft (150 sq ft) and 2 doors of 3 × 7 ft (42 sq ft): 1,260 + 240 − 150 − 42 = 1,308 sq ft. With 10% waste, 1,438.8 sq ft, or 14.39 squares. Order 14½ or 15 squares, depending on how your siding is packaged.
About openings and waste
Many installers don't subtract ordinary windows at all, because the pieces cut out around them are mostly scrap. One siding trade guide (Progressive Foam) says not to subtract window area unless it's a very large picture window, but to subtract garage doors, and to count gables as height × width × 0.75 (which builds in waste on the angled cuts). If you follow that method, set windows to 0 and use a smaller waste figure.
The waste allowance here defaults to 10%. Raise it for houses with lots of corners, dormers or short wall sections, and for patterns like shakes or board-and-batten.
What isn't included
- Trim and accessories: corner posts, J-channel, starter strip, soffit and fascia are bought by the linear foot, not the square.
- Packaging: boxes often hold 2 squares, and some products come in half or one-and-a-half squares. Round up to whole boxes.
- Furring or insulation board: if you're adding rigid foam under the siding, use the same net area.
Sources
How we checked this
Before every update, this calculator is run in a real browser with these known answers, and it must match all of them:
- Four walls (1,260 sq ft) + two 30 × 8 ft gables (240) − 10 windows (150) − 2 doors (42) = 1,308 sq ft ✓
- Same with 10% waste: 1,438.8 sq ft = 14.39 squares ✓
- One 20 × 10 ft wall, no openings, no waste: exactly 2 squares ✓
- Edge: openings bigger than the walls are refused ✓
Last checked October 26, 2026. Spotted something wrong? The math is done in your browser with the formula shown on this page, so you can check any result by hand.
Questions people ask
How many squares of siding do I need for a 2,000 sq ft house?
It depends on the wall area, not the floor area. A two-story 2,000 sq ft house (25 × 40 ft footprint, 18 ft walls) has 130 ft × 18 ft = 2,340 sq ft of wall, or 23.4 squares before gables, openings and waste; about 25.7 squares with 10% waste.
What is a square of siding?
100 square feet of wall coverage, a 10 × 10 ft area.
Should I subtract windows when measuring for siding?
For a tight estimate, subtract large openings like garage doors and picture windows. Many installers don't subtract small windows, because the cut-out pieces are rarely reusable.
How do I measure a gable for siding?
A triangle's area is ½ × base × height. A gable 30 ft wide and 8 ft tall is 120 sq ft.
How much waste should I add for siding?
This calculator uses 10% by default. Add more for complex walls with many corners and short runs.