Calcist

Style

Buttons

Spacing

How much to show

Decimal places

Text size

Board and batten calculator

Enter the wall size, the batten width and the most spacing you want to get the number of battens, the real even spacing, the linear feet and the boards to buy.

Private: calculated on your device. Nothing you type is sent anywhere.

Next: Painting it? The paint calculator covers the wall. Doing the outside? Get the area with the siding calculator.

How the battens are spaced

For a balanced look, the battens sit flush at both ends of the wall and the gaps between them are all the same. So the calculator finds the fewest equal gaps that keep the spacing at or under your maximum.

Gaps = (wall width in inches − batten width) ÷ max spacing, rounded up
Battens = gaps + 1
Real spacing, center to center = (wall width − batten width) ÷ gaps
Clear gap between battens = real spacing − batten width
Linear feet = battens × wall height + rails × wall width

Worked example

A 12 ft (144 in) wall, 8 ft high, with 2.5 in battens no more than 16 in apart: (144 − 2.5) ÷ 16 = 8.84, so 9 gaps and 10 battens. Real spacing = 141.5 ÷ 9 = 15.72 in on center, leaving 13.22 in of open wall between battens. Linear feet = 10 × 8 = 80 ft. Each 8 ft batten comes from one 8 ft board, so buy 10 boards, or 5 boards of 16 ft cut in half.

Boards to buy

The calculator counts whole pieces, not just linear feet, because short offcuts aren't much use. If a board is at least twice the wall height, it cuts into two or more battens. If the wall is taller than the board, each batten needs a joint and more than one board. Rails along the top or bottom run the width of the wall.

Tips

  • Exterior siding: battens cover the joints between panels or boards, so their spacing is set by the panel width, and they must be nailed through to framing. Follow the siding maker's installation guide.
  • Interior accent walls: 12 to 24 in spacing is typical. Mark the studs first so the battens can be nailed into them where they line up.
  • Nominal sizes: a 1×3 is about ¾ × 2½ in and a 1×4 is ¾ × 3½ in.
  • Buy a spare board or two for splits, bad ends and miscuts.

Sources

How we checked this

Before every update, this calculator is run in a real browser with these known answers, and it must match all of them:

  • 12 × 8 ft wall, 2.5 in battens, 16 in max: 10 battens ✓
  • Same wall: real spacing 141.5 ÷ 9 = 15.72 in ✓
  • Same wall with 16 ft boards: 5 boards ✓
  • 10 ft tall wall on 8 ft boards with a top rail: 20 + 2 = 22 boards ✓
  • Edge: spacing smaller than the batten is refused ✓

Last checked October 26, 2026. Spotted something wrong? The math is done in your browser with the formula shown on this page, so you can check any result by hand.

Add this calculator to your website (free)

Paste this code into any web page. The calculator works on your page, resizes itself, has no ads and no tracking cookies, and nothing your visitors type is sent anywhere. More about embedding.

Questions people ask

How far apart should battens be?

Usually 12 to 24 in on center for an interior wall, and about 16 in is a common middle ground. On exterior panel siding, the batten spacing follows the panel joints and framing.

How many battens for a 12 ft wall?

With 2.5 in battens no more than 16 in apart, 10 battens at 15.72 in on center. At 24 in max spacing, 7 battens at 23.58 in.

What size boards are used for board and batten?

Battens are often 1×2, 1×3 or 1×4. Exterior siding battens are commonly about 5/8 × 2½ in over panels.

How do I make the battens evenly spaced?

Subtract one batten width from the wall width and divide by the number of gaps. The calculator does this and gives the clear gap so you can cut a spacer block.

Do I need to nail battens into studs?

Outside, yes, through to framing as the siding maker specifies. Inside, nailing into studs where possible and using construction adhesive elsewhere is common.

Related calculators